Dual Band GPS / Iridium Antennas

This product is a combination active L1 GPS and passive Iridium antenna. Designed as a low cost, high performance, antenna to suite Satellite phone / data Modem applications. This antenna operates in the band used by Iridium Satellites.

Dual Band GPS – Iridium Antenna

Satellite Phone Auxiliary Antenna

The IGPSP99TP3 antenna was specifically designed for the Iridium frequency range. Magnetically mountable, this antenna is the ideal auxiliary antenna to improve reception in mobile applications. The antenna comes standard with a 3 metre cable tail and a TNC plug which should connect directly to your equipment or portable dock.

Satellite Phone Auxiliary Antenna

Rojone makes available two GPS amplifiers in our AMA-061 Series.

AMA-061B is our broadband GPS Amplifier and our AMA-061F is a high rejection GPS filtered.  Both these amplifiers are designed to boost GPS signals for long range transmission or for a GPS Repeater Kit.  Our filtered amplifier is ideal for boosting GPS signal in noisy environments.  These amplifiers can also be used as a DC feeder for a GPS antenna, additional amplifier or as a DC splitter.  The DC through can be regulated or by passed to the antenna for 5V systems.

GPS Amplifiers

High Power (400 Watts) Log Periodic Antenna

The AE-LPH-800-200-400W log periodic dipole antenna is designed to provide wideband directional transmission/ reception of radio signals from 800 to 2000 MHz bands. The compact size of the log periodic antenna allows easy handling and specially designed mounting arrangement results in fast installation. This high gain LPA provides strong performance over the entire frequency of 800-2000 MHz as the LPDA does not use loading technique to reduce the overall size of array. This log periodic antenna operates at D.C. ground with low resistance discharge path for protection against lightning and for immunity to noise. Output of log periodic antenna is provided via low loss coaxial cable at the back end of the antenna boom.

High Power (400 Watts) Log Periodic Antenna

Times Microwave have released the MaxGain Range of fully tested Cable Assemblies designed for Loss Critical performance. The cable is designed to work from DC to 18GHz and uses a revolutionary outer conductor geometry to provide ultra-stable low loss performance. Coupled with a full range of passivated stainless steel connectors these assemblies are ideally suited for applications where lowest loss and good stability with bending is required.

Features and Benefits

MaxGainTM Cable Assemblies

Presentations

Rojone has been in the connector business since 1978. We are experts in our field, stocking over 40,000 line items manufactured by leading international military and professional connector manufacturers such as Radiall, Times Microwave, Pasternack, Trompeter and Tajimi as well as designs specifically created by Rojone for unique customer applications. Rojone not only sells quality connectors, we offer an expert value added termination service, providing our clients with quick turn-around custom flexible or semi-rigid cable assemblies, manufactured by qualified IPC trained technicians, delivered 100% tested and ready to use.

AM/FM Connectors

	RO-AMFM62MSS	– AM/FM Car Antenna Plug
Between-Series Adaptors
	4.3-10	– In Series & Selection of Between Series Adaptors
	RO-BNCF-MCXM	– BNC Female to MCX Male Adaptor
	RO-BNCF-NFBH	– BNC Female to N Female Bulkhead Adaptor
	RO-716F-NF	-DIN 7/16 Female to N Female Adaptor
	RO-716M-NM	– DIN 7/16 Male to N Male Adaptor
	RO-NF-SMAMB	– N Female to SMA Male Bulkhead Adaptor
	RO-NF-SMAMRA	– N Female to SMA Right Angle Male Adaptor
	RO-SMAM-TNCM	– SMA Male to TNC Male Adaptor
BNC Connectors
	RO-BNC141FBH	– BNC Female Bulkhead Solder, suit EZ141 0.141? Semi Rigid Coax Cable
	RO-BNC75FPCB	– BNC Female PCB Mount, 75 Ohms
	RO-BNC240FBC	– BNC Female Bulkhead Crimp, suit LMR-240
DIN 7/16 Connectors
	RO-716F-F	– DIN 7/16 Female to Female Adaptor
	RO-716F45716F	- 45° DIN 7/16 Female to Female Adaptor
	RO-716F45716M	– 45° DIN 7/16 Female to Male Adaptor
	RO-716MCAPxxx	– DIN 7/16 Series Male Dust Cap, available in Aluminium, Brass and Stainless
MMCX Connectors
	RO-MMCX174MC	– MMCX Male Crimp, suit RG-174
N Connectors
	RO-NFSQFLSP	– N Female Square Flange Receptacle
	RO-N174FBC	– N Female Bulkhead Climp, suit RG174
	RO-N213MC	– N Male Clamp Captive Contact, suit RG213
	RO-N400MC	– N Male Crimp, suit LMR-400 series, Belden 9913 & 9914
	RO-N400MEZS	– N Male Ezi Fit Solder Clamp, suit LMR-400
	RO-N240MRAC	– N Male Right Angle Crimp, suit LMR-240
	RO-NF-M	– N In-Series Male to Female Low PIM Adaptor
	RO-NF-MRA	– N In-Series Male to Female Right Angle Low PIM Adaptor
QN Series
	RO-QN400MRA	- QN Series Right Angle Male Crimp Plugs for LMR400 Series Cables
SMA Connectors
	RO-SMAFBR-SMAFR	– SMA Female Bulkhead Reverse to SMA Female Reverse Adaptor
	RO-SMA174MRC	– SMA Male Reverse Crimp, suit RG174
	RO-SMAM-F-F	– SMA Male to SMA Female T-Adaptor
	RO-SMAMCAC	– SMA Male Protective Cap with Chain
TNC Connectors
	RO-TNCFR-FRB	– TNC Female Reverse to TNC Female Reverse Bulkhead Adaptor
	RO-TNCF-MRA	– TNC Female to Male Right Angle Adaptor
	RO-TNC174FBC	- TNC Female Bulkhead Crimp, suit LMR100 Series, M17-152, RG174, RG188, RG316 cables
TS9 Connectors
	RO-TS9174MC	TS9 Male Crimp, suit RG174

ROJ-E317 – Integrated UHF Transmit/Receive Multicoupler System

The ROJ-E317 product is a high performance integrated UHF transmit/receive multi-coupler system in a single enclosure suitable for 19 inch rack mounting. The hybrid combining technology drastically reduces the size of an overall system compared to traditional cavity based and multi-section filter type systems while still maintaining high levels of performance. All loads for the combiners are included inside the equipment as well as a highly flexible, reliable and efficient DC-DC power supply.
Two simultaneous 50 W transmit signals (Tx1, Tx2) can be applied to the equipment and combined for transmission onto a single external antenna (consult Rojone for suitable antennas). The same antenna can be used to receive signals at different frequencies to the transmitted signals with the equipment coupling out four copies of the received signal (Rx1, Rx2, Rx3, Rx4).
This combined transmit/receive setup allows for easy integration with a wide range of communication systems and applications such as multichannel voice and data transmission systems, base stations and repeaters.
As most applications are unique, the ROJ-E317 product can be configured to your specific requirement by selecting the most appropriate Tx and Rx frequency range and output connector combination (SMA, BNC, MCX, TNC, N type). Please talk to us about your individual needs

ROJ-E317 Datasheet
ROJ-E317 Manual V1

CAT7 E10 MHz 4-Pair solid S/FTP, Low Smoke, Zero Halogen Cable Violet Jacket

This is a fully shield cable with individual foils around each pair, coupled with high screen
coverage outer braid for a high level of immunity to outside interference’s.
In PoE remote power applications, this cable can be installed in environments up to 60
degrees Celsius without degradation suffered by heat rise inside the cable bundle. This 7A cable
can also be used for cable sharing from one drop ideal for running multiple lower speed
applications.

CAT7A-4PLSZH Cable

Ethernet is used as a standard interface for data transmission and SPINNER has developed a contactless coupler (also referred to as a module) that can be provided with different inner diameters.

In contrast to transmission by means of a traditional slip ring, the Ethernet module also supports Gigabit Ethernet irrespective of the dimensions, while the correct standard is detected and transmitted automatically (10 Base-T (10 Mbit/s) or Fast Ethernet (100 Mbit/s) or Gigabit Ethernet (1 Gbit/s) – i.e. Plug and Play.

The mechanical system has been designed in such a way that one or two transmission modules can be incorporated, also in combination with the DC/DC converter described below. The converter has been designed so that more than 50 watts with 24 V output voltage are still available to the user in addition to the rotor’s own power supply.

Without requiring any adjustments, the data transmitter is fully compatible with Profinet (class A + B); a version with CAN bus (repeater mode up to 500 Kbit/s) is also available.

Our contactless power transmission system is a rotationally symmetric system for contactless transmission of electrical energy. This transmission system is used for the DC voltage supply of control systems, sensors or other consumers on rotating shafts.

The functioning of the transmission system corresponds to that of a galvanically isolated DC voltage transmitter. It keeps the output voltage nearly constant regardless of the load and over a wide input voltage range. The output has a short-circuit-proof and open-circuit-proof design. A major advantage is the presence of a hollow shaft, which means that combinations with optical single-channel or multi-channel rotary joints are possible for data transmission. This DC/DC converter meets all standards common in the industry with respect to safety, interference immunity and emitted interference.

In the radar technology sector, the trend towards installing active components directly on the antenna is continuing. The radical reduction in cabling saves weight and increases the efficiency of the system. However, ever increasing amounts of data with high transmission rates also require demanding digital data transmission solutions. For radar rotary joints, this means that traditional HF modules for the different frequency bands are replaced by diverse media couplers, power current and signal transmission paths.
Transmission amplifiers, now installed on the
rotatable part of the radar antenna, require media couplers to create a cooling circuit in order to ensure cooling. Power current is traditionally supplied by means of a slip ring. The electrical signals to and from the active antenna equipment are no longer transmitted by a contacting slip ring but via a multi-channel fiber optical rotary joint or means of a contactless

Contactless Data & Power Transmission

Times Microwave Systems has recently introduced a new range of Data Line Surge Protectors. These products offer a unmatched level of data integrity and over-voltage protection, the LP-DOE-1G, LP-POE-1G and LP-PAE-100 Data Line surge protection devices are the newest additions to the Times-Protect® product family. Proprietary circuitry results in surge let-through voltage on data lines of less than 20V peak at 3kA 8x20uS surge test current and less than 10V peak at 100A 10x1000uS surge test current, while complying with extended RFC2544 test methods for data integrity. These extremely difficult tests are conducted on two protection devices separated by 100 meters of Cat 5e cable over a broad temperature range measuring these parameters:

Items available:

• LP-DOE-1G 1000 BASE-T ETHERNET DATA ONLY – 1000 Base-T / Indoor application with all data pin protected to chassis ground
• LP-POE-1G 1000 BASE-T POWER OVER ETHERNET – Power Over Ethernet, 1000 Base-T with up to 60Vdc injector. All pin pairs protected to chassis ground
• LP-PAE-100 100 BASE-T POWER AND ETHERNET – 00 Base-T with all pins protected to ground. Data pin pairs are (1-2) (3-6) and DC pin pairs are (4-5) (7-8)

The RFC2544 test results for each of these outstanding devices are available for download on the Times Microwave Systems website.
Enhanced RFC 2544 Test

Rojone is proud to sponsor the 2015 Australian Industry & Defence Network (AIDN) NSW Young Achiever Awards (YAA), which celebrates the achievements of young professionals working in the Australian Defence Industry. Rojone and AIDN recognise that driven and talented young people are the key to the future of the defence industry. In order to recognise individuals who may be future industry leaders, AIDN has created the AIDN Young Achiever Award and Rojone is pleased to support this important initiative.

The finalists for the 2015 NSW awards came from across the defence industry in NSW and demonstrated the talent and dedication working in this industry.

The winner was announced at the AIDN NSW 21st Anniversary Dinner held in Sydney in September and presented by Mr Steve Wearn, acting General Manager Commercial, Capability Acquisition and Sustainment Group. The 2015 AIDN Young Achiever is Christine Chen, who works for Thales in EM/RF Engineer in the Speciality Engineering Group. The runner up was Danya Henriksen, Project Officer Maintenance Planning, Petrolink Engineering with 3rd place going to Ryan McKay, Project Engineer, Forgacs-Broens.

The winner of the NSW award will be competing for the national Young Achiever’s Award against winners from the other states. This will be announced at the AIDN National 21st Anniversary Dinner on Monday 8th February 2016 in Canberra.

Rojone offers its congratulations to all entrants and finalists, and looks forward to supporting this award in the future.

The new SATEL-LP product family offers an extremely easy solution for simple I/O and serial communications. With software-free radio setup, SATEL-LP offers a cost-effective wireless solution where it is too costly or not possible to run a wire. All SATEL-LP modules are DIN rail mountable. The communications over the air interface is secured with a 128-bit AES encryption
and authentication. No need for RTU or PLC devices

SATEL-LP expansion modules offer direct connection of common industrial signals to the SATEL-LP radio modules, eliminating the need for RTU or PLC devices. Expansion modules are hot swappable and up to 32 expansion modules can be added to one SATEL-LP radio module.

Mesh networks with up to 250 nodes. Easy point-to-point or network structures such as line, star or mesh.

SATEL-LP24

SATEL-LP9

Product Brochure

Data Sheet

User Manual

Rojone Pty Ltd introduces the new 4.3-10 Connector series. Designed for major telecom equipment manufacturers, the 4.3-10 series is small and lightweight, features high performance/low intermodulation, and is suitable for both indoor and outdoor applications.
Lightweight 4.3-10 connectors offer these key features and performance characteristics:

• 30% smaller and 60% lighter than the comparable 7/16 square flange jack receptacle
• RF power up to 500 W @ 2 GHz
• Low intermodulation
• Frequency range: DC to 6GHz
• Meets IP68 Requirements
• Available in Screw, Hand Screw and Push-Pull formats

Importantly, on the 4.3-10, electrical & mechanical reference planes are separated with the ground contact sliding. Intermodulation performance is not linked to the installation torque – the contact pressure is a function of the contact design.

4.3-10 Connectors

For more information visit our website here

For more updates please follow us on Google+

The AE-JD-0820 Jammer Discone Antenna is a rugged all weather model, enclosed in an ABS radome, uses all ultra-corrosion resistant aluminium alloy does not require any field tuning or adjustments. The compact size of the omni-directional antenna allows easy handling, shipping and is highly suitable for transmitting & receiving without having the requirement of multiple antennas. The cylindrical enclosure is used for low wind loading and for minimal effect of ice formation on the antenna operation as well as providing an aesthetically pleasing appearance.
The jammer discone antenna is supplied complete in assembled condition. This discone antenna has smooth VSWR and constant gain over the 800-2000 MHz frequency band. The AE-JD-0820 jammer discone antenna consists of ultra-corrosion resistant radiating elements and is enclosed in ABS housing. The ABS has excellent transparency for radio signals and is mechanically robust to support extra mechanical strength to the discone antenna.

AE-JD-0820 Omin Jammer Antenna 800-2000MHz

Times Microwave has just released its new CAT6 SFTP LAN Data Cable, 4 pairs 23AWG

Featuring, high coverage tinned copper outer shield for superior grounding, better than 90dB RF Shielding effectiveness, ripcord for easy jacket stripping, 8mm O/D, black PE Jacket for excellent weather resistance.

TMS – Cat-6 Outdoor Rate & Shielded

Transit qualifications

Tajimi offers a range of Harsh environment miniature rectangular connectors.  Rojone stocks a range of Tajimi standard, micro, miniature & waterproof push/pull & bayonet locking commercial circular multipin connectors, MR01, 1108, R04. R28, R14, PRC03, PRC04, PRC05, PRC07, R03, R27, R05 & R29.

Van System Italy, exclusive represented in Australian & New Zealand by Rojone is pleased to announce the availability of Data transmission connector series GM – Module connector complete with New CAT 7 Modules and the EVBS Lan CAT5E /CAT6 Bayonet connectors.

GM – Modular data transmission connectors are Circular bayonet connector designed for railway rolling vehicle applications. This series can accept 4 or 7 modules both electrical and optical contact modules, independently house inside the IP67 rated GM mated Shell offering excellent water resistance together with superior shielding EMI/RFI protection. Modules are pneumatic sealed housing making the them ideally suitable for pressurised cabins installation.

The new CAT 7 Module features; over moulded contacts pairs to control impedance, 4 x 100 ohm pairs. Each pair is fully shielded from the adjacent to reduce crosstalk, contact terminations are available for 23, 24, and 26+ AWG, easy and reliable assembly.

EVBS is a new reliable solution for LAN Cat5E or Cat6 data transmission for Railway applications.
This bayonet coupling connector is compact, vibration & shock resistant, IP67 water resistant, mated, easy to connector to most common conduit systems, materials and shielding complies with the latest railway requirements fully tested. 2 or 4 twisted pairs with or without shielding insert arrangements.

GM Module Cat5, Cat6, Cat7 Connectors Van Systems Italy

Van System Italy, exclusive represented in Australian & New Zealand by Rojone is pleased to announce the availability of an extensive range power Connector designed for power distribution, utilities, electric vehicle, railway equipment, military field power, mobile generator, load banks & back up power system applications.

Powerline – Single pole, power connectors up to 630A for railway equipment, power distribution, electric vehicles. Powerline features, EN Harmonised phase identification colour coding, Mated IP68 Sealed, 500 mating cycles, UL94 VO Flame retardant, EN/ESI compliance, clip retained contacts up to 630A, 2000V rated voltage to earth, spring loaded locking, suitable for cables sizes from 25 to 300mm2, IP2x finger protected in unmated condition for both supply and load connector, modular system for daisy chain configurations

Powerline Single Pole Power Connectors Van Systems Italy

Vanten – Single pole, power connector up to 400A for railway equipment, power distribution. Vanten is IP67 sealed mated, 5 key polarisation system & colour coding to prevent connection errors, compact in size, suitable for cables sizes from 16 to 120mm2, IP2x finger protected in unmated condition for both supply and load connector, no special tooling for assembly or uncoupling, EN61984, IEC60529 & BS7909 compliant.

VANTEN Series 400A Single Pole Power Connectors Van Systems Italy

CP090313 Series single pole bayonet connectors & up to 6 contacts in a ruggedized rectangular housings designed for railway power applications.

Lugit – is a safe & effective temporary connection/extension for single core power cables that are pre-terminated with copper lug terminals. Easy to use, reusable, IP967 when mated, accepts lug sizes 185mm2, 240mm2 & 300mm2 with 12mm holes, facilitates cable diameters from 14.5-37mm O/D, 2 minutes to assemble, no special tools field installable, no need for connectors or junction boxes, lightweight & colour bands for phase identification.

LUGIT Lugged Power Cables Connection System Van Systems Italy

Van System Italy, exclusive represented in Australian & New Zealand by Rojone is pleased to announce the availability of an extensive range railway connectors, including circular bayonet coupling power & signal connectors, high density power rectangular Connector and, Data transmission connector series GM – Module connector complete with New CAT 7 Modules and the EVBS Lan CAT5E /CAT6 Bayonet connectors.

Circular Bayonet Coupling connectors designed for railway applications, this range features many configuration options, environment sealing, rubber coatings to protect against accidental drop, Van-Systems unique roller stud to enhance the bayonet locking mechanism, reduce friction, retains mating force during vibration and lowers the wear of the coupling ramps in repeated mating situations. Ferrovia Light

KVBS -Bayonet coupling complies NFF61030 Railway specifications.

KVBS Bayonet Coupling Complies NFF 61030 Connectors

GM – Modular data transmission connectors are Circular bayonet connector designed for railway rolling vehicle applications. This series can accept 4 or 7 modules both electrical and optical contact modules, independently house inside the IP67 rated GM mated Shell offering excellent water resistance together with superior shielding EMI/RFI protection. Modules are pneumatic sealed housing making the them ideally suitable for pressurised cabins installation.

The new CAT 7 Module features; over moulded contacts pairs to control impedance, 4 x 100 ohm pairs. Each pair is fully shielded from the adjacent to reduce crosstalk, contact terminations are available for 23, 24, and 26+ AWG, easy and reliable assembly.

GM Module Cat5, Cat6, Cat7 Connectors Van Systems Italy

EVBS is a new reliable solution for LAN Cat5E or Cat6 data transmission for Railway applications.
This bayonet coupling connector is compact, vibration & shock resistant, IP67 water resistant, mated, easy to connector to most common conduit systems, materials and shielding complies with the latest railway requirements fully tested. 2 or 4 twisted pairs with or without shielding insert arrangements.

Powerline – Single pole, power connectors up to 630A for railway equipment, power distribution, electric vehicles. Powerline features, EN Harmonised phase identification colour coding, Mated IP68 Sealed, 500 mating cycles, UL94 VO Flame retardant, EN/ESI compliance, clip retained contacts up to 630A, 2000V rated voltage to earth, spring loaded locking, suitable for cables sizes from 25 to 300mm2, IP2x finger protected in unmated condition for both supply and load connector, modular system for daisy chain configurations

Powerline Single Pole Power Connectors

Vanten – Single pole, power connector up to 400A for railway equipment, power distribution. Vanten is IP67 sealed mated, 5 key polarisation system & colour coding to prevent connection errors, compact in size, suitable for cables sizes from 16 to 120mm2, IP2x finger protected in unmated condition for both supply and load connector, no special tooling for assembly or uncoupling, EN61984, IEC60529 & BS7909 compliant.

VANTEN Series 400A Single Pole Power Connectors

CP090313 Series single pole bayonet connectors & up to 6 contacts in a ruggedized rectangular housings designed for railway power applications.

CP 090313 Power Connectors for Railway

Lugit – is a safe & effective temporary connection/extension for single core power cables that are pre-terminated with copper lug terminals. Easy to use, reusable, IP967 when mated, accepts lug sizes 185mm2, 240mm2 & 300mm2 with 12mm holes, facilitates cable diameters from 14.5-37mm O/D, 2 minutes to assemble, no special tools field installable, no need for connectors or junction boxes, lightweight & colour bands for phase identification.

LUGIT Lugged Power Cable Connection System